Liquid applied polyurethane system
Polyurethane liquid roofing membranes are the professional, durable, waterproofing solution
Plasticizer For Concrete Mix
Plasticizers are the admixtures which are primarily used to increase workability of concrete along with decreasing water to cement ratio thus increasing strength of the concrete.
Form release agent/ Shuttering Oil
Shuttering Oil or formwork oil is high-quality mineral oil that is applied to the inner surface of formwork before concreting. Shuttering oil is also known as a form or mould release agent.
Bituminous Felt Membrane
Bituminous felt is waterproof sheeting used for surfacing roofs or as an underlay beneath tiles or slates
Enhanced adhesion to smooth surfaces: dense concrete, steel etc.
Suitable for potable water
Swells up to 700% when in contact with water and will return to its original size if the concrete and substrate become dry.
Grout is generally a mixture of water, cement, and sand and is employed in pressure grouting, embedding rebar in masonry walls, connecting sections of pre-cast concrete, filling voids, and sealing joints such as those between tiles.
Waterstops and Waterbar
Waterstops or waterbars are flexible tape like elements of a concrete structure that prevent the passage of water through concrete joints.
EPDM is an extremely durable synthetic rubber roofing membrane (ethylene propylene diene terpolymer) widely used in low-slope buildings in the United States and worldwide. Its two primary ingredients, ethylene and propylene, are derived from oil and natural gas
Tile adhesive and grout is used for bonding and sealing tiles. Tile adhesive is applied first to fix tiles to wall or floor surfaces
Polyurethane Primer for Concrete and Steel | deep penetrating | superior corrosion, abrasion, water resistace | Moisture Cured
Spalled concrete, delaminated concrete, and concrete which has suffered from freeze-thaw or impact damage.
Cementitious waterproofing is a waterproofing method for concrete that uses cement-based polymer coatings to create a barrier to water and moisture
Our products are spray applied or brush applied in liquid form, penetrating the smallest cracks & crevices and then sets within seconds to form a hard but flexible permanent air and watertight bond to the substrate.
Crystalline coating is a technology which is designed primarily for an additional protection of underground concrete parts of buildings against moisture and subsurface water.
Crystalline Waterproofing Admixture
crystalline admixture used to create permanently waterproof concrete
Acrylic resin offer better stain protection, greater water resistance, better adhesion, greater resistance to cracking and blistering, and resistance to alkali cleaners.
Sanitary ware and Window sealant
Sanitary sealant is used to seal surfaces in areas with high condensation. Also known as bath sealant or shower sealant, they are specifically designed for use in a wet environment because of their water, mould and mildew-resistance properties.
Spray applied Polyurethane Foam Thermal insulation system
Spray Foam Insulation: Spray foam stops moisture accumulation by reducing air infiltration and air intrusion. In addition, closed-cell spray polyurethane foam retards both heat transfer and water vapor transfer, making it an ideal material for use with flow-through designed building assemblies.
Tile grouting solutions
There are three main types of grout: cementitious grouts composed of a Portland cement base; epoxy grouts, and furan grouts,
Rebar primer and corrosion inhibitors
Corrosion inhibiting primers help protect reinforcing steel against corrosion, extending the life of structures and reducing maintenance.
Concrete curing compound
Concrete curing compound is a compound which helps to prevent the loss of moisture content from the concrete. So, concrete is properly cured which results the full development of strength of concrete
Concrete floor hardener
Concrete densifier and chemical hardener compound is a proprietary, water-based, ready-to-use, clear silicate liquid, formulated with chemically…….
Pouring grade Expansion Joint Sealant
Gun Grade is a two-component joint sealant, based on a liquid polysulphide polymer which, when mixed and applied cures to form a tough rubber-like seal